Panel Upgrades in Roseville, CA
Panel upgrades and replacements are Rooster Electric’s specialty — and Roseville is full of the homes that need them: 100-amp panels from the building-boom decades, including the Zinsco, Federal Pacific, and Challenger panels insurers keep flagging.
Typical price in Roseville: $4,725–$6,825 for most 200A upgrades — a rough, typical range only, and a home’s actual price can fall outside it. Permit, utility coordination, and inspections are included, with a 10-year workmanship warranty. Estimates, not quotes — your written price is confirmed after a photo review or a visit.
How panel work runs in Roseville
Roseville runs on Roseville Electric — the city's own utility, not SMUD or PG&E — and Rooster Electric is a Roseville Electric approved contractor. That matters: panel work here follows Roseville Electric's approval process alongside the City of Roseville permit, and we build both into the schedule from day one so approval isn't the bottleneck.
The older core near Old Town carries the problem brands; the newer west-side subdivisions usually already have 200A service, so Roseville panel calls split sharply — replacement for the old stock, capacity answers for the new.
The known-risk brands we replace here
- Zinsco (also Sylvania-Zinsco) — breakers documented to melt to the bus bar and fail to trip.
- Federal Pacific Stab-Lok — breakers that can fail to trip on overload; a known insurance flag.
- Challenger — breakers and bus connections prone to overheating.
If one of these is on your wall, we photograph what we find and show you — the fix is replacement, and we will walk you through the options before you commit to anything.
How the job goes
- Send panel photos or book a site visit — we confirm panel, service type, and siding
- Written price confirmed before anything is scheduled
- We file the permit and utility application
- Install day: power off, panel swapped, power restored same day in most cases
- City inspection and utility meter release to close it out
Recent panel jobs near Roseville
Rooster Electric Co on Google: 5.0 ★ · 150+ reviews
200A panel replacement (overhead service) + dedicated 20A kitchen circuit
200A panel replacement in Roseville. We replaced the old overhead-service panel with a new 200A meter-main panel on a new service riser, with every circuit labeled and tested, and added a dedicated 20A circuit for the kitchen. The work was permitted and inspected with the City of Roseville, coordinated with Roseville Electric.
Spa disconnect / sub panel replacement
Spa disconnect and sub panel replacement in Roseville — Rooster Electric replaced the spa disconnect box and spa sub panel and installed a GFCI breaker for protection. The work restores safe spa power for a Roseville home. Panel and sub panel work in Roseville Electric territory.
Panel questions — Roseville
How much does a panel upgrade cost in Roseville?
Typically $4,725–$6,825 for 200A, including the City of Roseville permit and Roseville Electric coordination. That’s a rough, typical range only — your home’s actual price can fall outside it. Stucco homes — common in Roseville — can land higher for patch coordination.
Are you a Roseville Electric approved contractor?
Yes. Rooster Electric is approved with Roseville Electric (and SMUD), and their service approval is part of every panel job we do in Roseville.
My Roseville home is on stucco. Does that change the job?
It changes the finish work, not the electrical scope. We set the panel into the stucco and coordinate the patch so it doesn't look like a patch — priced in your written quote up front.
What does a panel upgrade cost with Rooster Electric?
A typical 200-amp panel upgrade with Rooster Electric runs roughly $4,725–$6,825. That is a rough, typical range, not a guarantee — your home’s actual price can fall outside it. Whether your service is overhead or underground, what your utility requires, and whether the panel can stay where it is all move the number. This is an estimate, not a quote: send clear panel photos or book a look in person and you get an exact price in writing — permit included, no surprises added later.
My panel says Zinsco, Federal Pacific, or Challenger. Can you replace it?
Yes, and it is some of the most common work we do. These brands have breakers documented to fail to trip, which is why insurers and home inspectors flag them. We swap them for a modern, code-compliant panel, permitted and inspected, and coordinate the utility side for you.
Who deals with my city and my utility on a panel job?
Rooster Electric does, start to finish. We file the city or county permit, work through SMUD, Roseville Electric, or PG&E approval and meter release, and schedule the final inspection — it is all one contract, so nothing stalls between offices on your time.
How long am I without power during a panel replacement?
Only while the swap itself is happening — for most homes that is part of one working day, with power back the same day. The longer part is lining up the permit and utility dates first, and we confirm your install day once the utility date is set.
Do I need to be home for the final panel inspection?
Yes — plan to be there to let the inspector in for a short visit to the panel or garage. We will not be on site for that final inspection, which is standard on these jobs. We send the permit ahead for you to print and keep with the panel.
Get your Roseville panel priced
Send a photo of your panel with the door open, or call (916) 235-3596 — most Roseville panel prices are confirmed from photos, in writing.

